You are reading the article Back To Stock/Downgrade Samsung Galaxy Trend Gt updated in December 2023 on the website Bellydancehcm.com. We hope that the information we have shared is helpful to you. If you find the content interesting and meaningful, please share it with your friends and continue to follow and support us for the latest updates. Suggested January 2024 Back To Stock/Downgrade Samsung Galaxy Trend Gt
WARNING!
Warranty may be void of your device if you follow the procedures given on this page.
You only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.
SAMSUNG GALAXY TREND GT-S7392 OFFICIAL JELLY BEAN 4.1.2 FIRMWAREBefore you begin with guide instructions below, make sure your android device is adequately charged — at least 50% battery of the device.
STEP 0: CHECK DEVICE MODEL NO.To make sure your device is eligible with this, you must first confirm its model no. in ‘About device’ option under Settings. Another way to confirm model no. is by looking for it on the packaging box of your device. It must be GT-S7392!
Do not use the procedures discussed here on any other variant of Galaxy Trend or any other device of Samsung or any other company. You have been warned!
STEP 1: BACKUP YOUR DEVICEBack up important data and stuff before you start playing around here as there are chances you might lose your apps and app-data (app settings, game progress, etc.), and in rare case, files on the internal memory, too.
For help on Backup and Restore, check out our exclusive page on that linked right below.
► ANDROID BACK UP AND RESTORE GUIDE: APPS AND TIPS
STEP 2: INSTALL LATEST DRIVERYou must have proper and working driver installed on your windows computer to be able to successfully flash stock firmware on your Samsung Galaxy Trend. In case you’re not sure, follow the link below for a definitive guide for installing driver for your Galaxy Trend on your computer.
► SAMSUNG GALAXY TREND DRIVERS INSTALLATION GUIDE
STEP 3: INSTALLATION INSTRUCTIONS DOWNLOADSDownload the Odin zip file and firmware file given below. Transfer both Odin and firmware file to a separate folder on your computer just to keep things tidy.
ODIN ZIP FILE FIRMWARE ZIP FILE STEP-BY-STEP GUIDEImportant Note: Backup important files stored on internal SD card of your device, so that in case a situation arises requiring you to do a factory reset after flashing stock firmware, which might format internal sd card too, your files will remain safe on PC.
Extract/Unzip the Odin zip file, Latest Odin3 v3.09.zip on your computer (using 7-zip free software, preferably) to get this file: Odin3 v3.09.exe
Extract/Unzip the Firmware zip file, S7392DDUAMJ4_S7392ODDAMJ1_INU.zip on your computer (using 7-zip free software, preferably) to get this file: S7392DDUAMJ4_S7392ODDAMJ1_S7392DDUAMJ2_HOME.tar.md5
Move the firmware file, S7392DDUAMJ4_S7392ODDAMJ1_S7392DDUAMJ2_HOME.tar.md5, in the same folder in which you extracted Latest Odin3 v3.09.zip (Just for your convenience, that is). So, now you’ll have the following files in that folder:
Odin3 v3.09.exe
S7392DDUAMJ4_S7392ODDAMJ1_S7392DDUAMJ2_HOME.tar.md5
Disconnect the Galaxy Trend from PC if it is connected.
Boot your Samsung Galaxy Trend into Download Mode:
Power off your phone first and wait for 6-7 seconds after display is off
Press and hold these 3 buttons together until you see Warning! screen: Volume Down + Power + Home
If you don’t get the Added! message, here are some troubleshooting tips:
Make sure you have installed driver for Galaxy Trend as said above.
If you have already installed driver, then uninstall them and re-install back.
Connect using a different USB port on your PC.
Try a different USB cable. The original cable that came with your phone should work best, if not, try any other cable that’s new and of good quality.
Reboot phone and PC and then try again.
Load the firmware file (extracted in Step 2) into Odin as instructed below:
Now in the Option section of Odin, make sure that Re-Partition box is unchecked. (Auto Reboot and F. Reset Time boxes remain checked, while all other boxes remain unchecked.)
Double check the above two steps.
If you see FAIL message instead of the PASS in Odin’s top left box, that’s a problem. Try this now: disconnect your Galaxy Trend from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 6 of this guide again.
Also, If device is Stuck at setup connection or on any other process, then too, try this: disconnect your Trend from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 6 of this guide again.
FEEDBACK US!Your suggestions and queries, if any, are most welcomed!
You're reading Back To Stock/Downgrade Samsung Galaxy Trend Gt
Back To Stock: Get The Official Android 4.1.2 Update For Samsung Note Gt
WARNING!
Warranty may be void of your device if you follow the procedures given on this page.
You only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.
SAMSUNG GALAXY NOTE GT-N7000 OFFICIAL JELLY BEAN 4.1.2 FIRMWAREBefore you begin with guide instructions below, make sure your android device is adequately charged — at least 50% battery of the device.
STEP 0: CHECK DEVICE MODEL NO.To make sure your device is eligible with this, you must first confirm its model no. in ‘About device’ option under Settings. Another way to confirm model no. is by looking for it on the packaging box of your device. It must be GT-N7000!
Do not use the procedures discussed here on any other Galaxy Note (including the Galaxy Note variant at T-Mobile, AT&T and other International variants) or any other device of Samsung or any other company. You have been warned!
STEP 1: BACKUP YOUR DEVICEBack up important data and stuff before you start playing around here as there are chances you might lose your apps and app-data (app settings, game progress, etc.), and in rare case, files on the internal memory, too.
For help on Backup and Restore, check out our exclusive page on that linked right below.
► ANDROID BACK UP AND RESTORE GUIDE: APPS AND TIPS
STEP 2: INSTALL LATEST DRIVERYou must have proper and working driver installed on your windows computer to be able to successfully flash stock firmware on your Samsung Galaxy Note. In case you’re not sure, follow the link below for a definitive guide for installing driver for your Galaxy Note on your computer.
► SAMSUNG GALAXY NOTE DRIVERS INSTALLATION GUIDE
STEP 3: INSTALLATION INSTRUCTIONS DOWNLOADSDownload the Odin zip file and firmware file given below. Transfer both Odin and firmware file to a separate folder on your computer just to keep things tidy.
ODIN ZIP FILE FIRMWARE ZIP FILE STEP-BY-STEP GUIDEImportant Note: Backup important files stored on internal SD card of your device, so that in case a situation arises requiring you to do a factory reset after flashing stock firmware, which might delete internal sd card too, your files will remain safe on PC.
Extract/Unzip the Odin zip file, Latest Odin3 v3.09.zip on your computer (using 7-zip free software, preferably) to get this file: Odin3 v3.09.exe
Extract/Unzip the Firmware zip file, N7000DDLSC_N7000ODDLSC_INU.zip on your computer (using 7-zip free software, preferably) to get this file: N7000DDLSC_N7000ODDLSC_N7000DLS6_HOME.tar.md5
Move the firmware file, N7000DDLSC_N7000ODDLSC_N7000DLS6_HOME.tar.md5, in the same folder in which you extracted Latest Odin3 v3.09.zip (Just for your convenience, that is). So, now you’ll have the following files in that folder:
Odin3 v3.09.exe
N7000DDLSC_N7000ODDLSC_N7000DLS6_HOME.tar.md5
Disconnect the Galaxy Note from PC if it is connected.
Boot your Samsung Galaxy Note into Download Mode:
Power off your phone first and wait for 6-7 seconds after display is off
Press and hold these 3 buttons together until you see Warning! screen: Volume Down + Power + Home
If you don’t get the Added! message, here are some troubleshooting tips:
Make sure you have installed driver for Galaxy Note as said above in ‘Before you begin..’ section.
If you have already installed driver, then uninstall them and re-install back.
Connect using a different USB port on your PC.
Try a different USB cable. The original cable that came with your phone should work best, if not, try any other cable that’s new and of good quality.
Reboot phone and PC and then try again.
Load the firmware file (extracted in Step 1) into Odin as instructed below:
Now in the Option section of Odin, make sure that Re-Partition box is unchecked. (Auto Reboot and F. Reset Time boxes remain checked, while all other boxes remain unchecked.)
Double check the above two steps.
If you see FAIL message instead of the PASS in Odin’s top left box, that’s a problem. Try this now: disconnect your Galaxy Note from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 3 of this guide again.
Also, If device is Stuck at setup connection or on any other process, then too, try this: disconnect your Note from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 3 of this guide again.
FEEDBACK US!Your suggestions and queries, if any, are most welcomed!
Latest Twrp Recovery For Samsung Galaxy S3 Gt
The international variant being, of course, the most widely used variant of the Galaxy S3, has a large development base.
Recently, Team Win has pushed out on update for GT-I9300 which promises to be void of the recovery in-compatibility issue with KitKat ROMs, which was due to ‘set metadata recursive’ error.
Now, all the Android 4.4 ROMs available for International Galaxy S3 like CyanogenMod 11, ParanoidAndroid, SlimKat, etc will be fully functional with this latest version of TWRP Recovery.
At the time of posting, the latest version of TWRP recovery for the International Variant of Galaxy S3 is 2.6.3.1.
WARNING!
Warranty may be void of your device if you follow the procedures given on this page!
You only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.
CHECK DEVICE MODEL NO.
To make sure your device is eligible with this, you must first confirm its model no. in ‘About device’ option under Settings. Another way to confirm model no. is by looking for it on the packaging box of your device. It must be GT-I9300!
Please know that this page is meant only for Samsung Galaxy S3, model no. GT-I9300. Please DO NOT try the procedures given here on other variants of the Galaxy S3: GT-I9305/GT-I9305T, or the S4 sets at US Cellular, AT&T, Verizon, Sprint, and others who have different model no.
BEFORE YOU BEGIN..
You must do this pre-installation stuff before attempting to install TWRP Recovery on your International Galaxy S3 in order to avoid any complications later, and have a smooth and successful process.
BACK UP YOUR DEVICEBack up important data and stuff before you start playing around here as there are chances you might lose your apps and app-data (app settings, game progress, etc.), and in rare case, files on sd card, too.
For help on Backup and Restore, check out our exclusive page on that linked right below.
► ANDROID BACK UP AND RESTORE GUIDE: APPS AND TIPS
INSTALL GALAXY S3 DRIVERYou must have proper and working driver installed on your windows computer to be able to successfully flash TWRP Recovery on your Samsung Galaxy S3. In case you’re not sure, follow the link below for a definitive guide for installing driver for your Galaxy S3 on your computer.
► SAMSUNG GALAXY S3 DRIVERS INSTALLATION GUIDE
CHARGE YOUR DEVICESIf your android device, or PC, powers off due to lack of battery while the process is underway, it could damage the device.
So, make sure both of them are adequately charged and that no power interruption takes place when the process is undergoing — at least 50% battery of the device and laptop is what we would recommend.
OTHER THINGS TO TAKE CARE OF:└ Use original USB cable to connect your phone to PC.
└ Do not use the procedures given below on Mac (using VMWare) as it works best on proper Windows PC only.
EXAMPLE VIDEO
If you haven’t used Odin software to install a recovery on a Samsung galaxy device before, we suggest you first watch a video of that, given right below, to get familiar with the process.
Btw, the video below shows installing the the CWM (Yes, not TWRP) recovery on Samsung Galaxy S3, but as the process is exactly same, it doesn’t matter.
GUIDE: SAMSUNG GALAXY S3 TWRP RECOVERY
DOWNLOADS
Download the file given below and save them in a separate folder on your computer (just to keep things tidy, that is).
File name: samsung-galaxy-s3-i9300-twrp-odin.zip (8.2 MB)
STEP-BY-STEP GUIDE
Extract/Unzip the TWRP Recovery file, samsung-galaxy-s3-i9300-twrp-odin.zip on your computer (using 7-zip free software, preferably). You’ll get the following files:
Odin3 v3.09.exe
Odin3.ini
openrecovery-twrp-2.6.3.1-i9300.tar
Disconnect the Galaxy S3 from PC if it is connected.
Boot your International Galaxy S3 into Download Mode: (The image below of Galaxy Note 2 would help)
Power off your phone first and wait for 6-7 seconds after display is off.
Press and hold these 3 buttons together until you see Warning! screen: Volume Down + Power + Home.
If you don’t get the Added! message, here are some
troubleshooting tips
:
Make sure you have installed driver for Galaxy S3 as said above in ‘Before you begin..’ section.
If you have already installed driver, then uninstall them and reinstall back.
Connect using a different USB port on your PC.
Try a different USB cable. The original cable that came with your phone should work best, if not, try any other cable that’s new and of good quality.
Reboot phone and PC and then try again.
Load the recovery file (extracted in Step 1) into Odin as instructed below:
Now in the Option section of Odin, make sure that Re-Partition box is unchecked. (Auto Reboot and F. Reset Time boxes remain checked, while all other boxes remain unchecked.)
Double check the above two steps.
If you see FAIL message instead of the RESET in Odin’s top left box, that a problem. Try this now: disconnect your Galaxy S3 from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 3 of this guide again.
Also, If device is Stuck at setup connection or on any other process, then too, try this: disconnect your Galaxy S3 from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 3 of this guide again.
Feedback Us!
It was easy, right? Let us know what you plan to do now, with latest TWRP Recovery installed. Looking to install Android 4.4 KitKat maybe, eh?
Suggestions are most welcomed!
Install Philz Touch Advanced Cwm Recovery On Samsung Galaxy Grand Duos Gt
WARNING!
Warranty may be void of your device if you follow the procedures given on this page.
You only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.
GUIDE: INSTALL PHILZ ADVANCED CWM RECOVERY ON SAMSUNG GALAXY GRAND DUOS
Before you begin with the instructions below, make sure your android device is adequately charged — at least 50% battery of the device.
STEP 0: CHECK DEVICE MODEL NO.
To make sure your device is eligible with this, you must first confirm its model no. in ‘About device’ option under Settings. Another way to confirm model no. is by looking for it on the packaging box of your device. It must be GT-I9082!
Please know that this page is meant only for Samsung Galaxy Grand Duos. Please DO NOT try the procedures given here on any other device of Samsung or any other company. You have been Warned!
STEP 1: BACKUP YOUR DEVICE
Back up important data and stuff before you start playing around here as there are chances you might lose your apps and app-data (app settings, game progress, etc.), and in rare case, files on the internal memory, too.
For help on Backup and Restore, check out our exclusive page on that linked right below.
► ANDROID BACK UP AND RESTORE GUIDE: APPS AND TIPS
STEP 2: INSTALL LATEST DRIVER
You must have proper and working driver installed on your windows computer to be able to successfully flash recovery on your Samsung Galaxy Grand Duos.
In case you’re not sure, follow the link below for a definitive guide for installing driver for your Samsung device on your computer.
► SAMSUNG DEVICES DRIVERS INSTALLATION GUIDE
STEP 3: INSTALLATION INSTRUCTIONS
DOWNLOADSDownload the files given below and transfer it to a separate folder on your computer (just to keep things tidy, that is).
CWM RECOVERY FILEFor latest version of the Recovery, check the original page →
ODIN ZIP FILE STEP-BY-STEP GUIDEImportant Note: Backup important files stored on internal SD card of your device, so that in case a situation arises requiring you to do a factory reset after flashing the CWM Recovery, which might delete internal sd card too, your files will remain safe on PC.
Extract
/Unzip the Odin
zip file
, Latest Odin_ v3.09.zip on your computer (using 7-zip free software, preferably) to get the following files:
Odin3 v3.09.exe
Odin3.ini
Download the Philz CWM file, philz_touch_6.12.8-i9082.tar.md5 and place it in the same folder in which you extracted Latest Odin_v3.09.zip (Just for your convenience, that is). So, now you’ll have the following files in that folder:
Odin3 v3.09.exe
Odin3.ini
philz_touch_6.12.8-i9082.tar.md5
Disconnect the Galaxy Grand Duos from PC if it is connected.
Boot your Galaxy Grand Duos into Download Mode:
Power off your phone first. Wait for 6-7 seconds after display is off.
Press and hold these 3 buttons together until you see Warning! screen: Volume Down + Power + Home.
Press Volume Up now to continue to Download Mode.
If you don’t get the Added! message, here are some troubleshooting tips:
Make sure you have installed driver for Galaxy Grand Duos as said above in ‘Before you begin..’ section.
If you have already installed driver, then uninstall them and reinstall back.
Connect using a different USB port on your PC.
Try a different USB cable. The original cable that came with your phone should work best, if not, try any other cable that’s new and of good quality.
Reboot your phone and PC and then try again.
Load the recovery file in chúng tôi form into Odin as instructed below:
Now in the Option section of Odin, make sure that Re-Partition box is unchecked. (Auto Reboot and F. Reset Time boxes remain checked, while all other boxes remain unchecked.)
Double check the above two steps. (Step 7 and Step 8)
When you get PASS! message, your device will restart automatically. You can then disconnect your phone from PC.
If you see FAIL message instead of the PASS in Odin’s top left box, that’s a problem. Try this now: disconnect your Galaxy Grand Duos from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 3 of this guide again.
Also, If device is Stuck at setup connection or on any other process, then too, try this: disconnect your Galaxy Grand Duos from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 3 of this guide again.
FEEDBACK US!
Your suggestions and queries, if any, are most welcomed!
How To Install Stock Recovery And Cache On Sprint Samsung Galaxy S6 Edge Manually
For Samsung Galaxy S6 users who have rooted their devices with CF Auto root and want to return to stock recovery which comes pre-installed with the device, here is a guide to do so. As you may be knowing, any changes you make to system partition makes your device incompatible with OTA updates, and the only way to accept OTA updates again is flashing Samsung stock recovery and cache partition back.
But btw, if you have changes to system partition yourself, other than CF Auto Root, then you will need to restore them back to and flashing a stock recovery won’t do alone — you will need to flash whole firmware again, which is also provided below.
All in all, if you have used CF Auto Root and have not done any other changes to system, restoring the stock recovery and cache will do for you to accept OTA update. However, if you have made a lot of changes to system, like deleting system apps, installing xposed framework, etc. flashed mods into recovery, then you need to flash the full firmware file below.
Let’s see how to install stock recovery back on Sprint Galaxy S6 running OCF firmware, to get OTA ability of the device back.
NOTE: Installing a firmware (large download of 1.5 GB is fine, and it covers recovery too. But if you are running OCF firmware (see step 1 below) and have only rooted using CF Auto Root, then we suggest you simply install the OCF recovery, a small download, to get OTA back.
Supported devices
SAMSUNG SPRINT GALAXY S6, model no. SM-G925P
Don’t try on any other S6 set with different model no, or any other device whatsoever
Disclamer: Installing stock recovery through Odin doesn’t void your device’s warranty, but it remains an unofficial process and thus you need to be cautious of it. In any case, you only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.
Important Note: Backup important files stored on your device before proceeding with the steps below, so that in case something goes wrong you’ll have backup of all your important files. Sometimes, Odin installation may delete everything on your device!
Installation Instructions:
Download Odin and firmware file from above.
Extract the Odin file. You should get this file, Odin3 chúng tôi (other files could be hidden, hence not visible). Also extract the firmware file, SPR-G925PVPU1AOCF-20230415164450.zip, if you intend to flash the firmware instead of recovery file.
Disconnect your Galaxy S6 Edge from PC if it is connected.
Boot Sprint Galaxy S6 Edge into download mode:
Power off your S6 Edge. Wait 6-7 seconds after screen goes off.
Press and hold the three buttons Volume Down + Power + Home together until you see warning screen.
Press Volume Up to continue to download mode.
Connect your Galaxy S6 Edge to PC now using USB cable. Odin should recognize your S6 Edge. It’s a must. When it recognizes, you will see Added!! message appearing in the Log box in bottom left, and the first box under ID:COM will also show a no. and turn its background blue. Look at the pic below.
You cannot proceed until Odin recognizes your device and you get the Added!! message.
If it doesn’t, you need to install/re-install drivers again, and use the original cable that came with device. Mostly, drivers are the problem.
Make sure Re-partition checkbox is NOT selected, under the Options tab. Don’t use PIT tab either. Go back to Log tab btw, it will show the progress when you hit start button in next step
If Odin gets stuck at setup connection, then you need to do steps 4 to 11 again. For this, close Odin, disconnect your S6 Edge, remove battery, insert it back after 5-6 seconds and then start from step 6 again.
Once reboot you are ready to go.
Root Samsung Galaxy Exhibit Sgh
WARNING!
Warranty may be void of your device if you follow the procedures given on this page.
You only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.
GUIDE: ROOT SAMSUNG GALAXY EXHIBIT SGH-T599
Before you begin with the instructions below, make sure your android device is adequately charged — at least 50% battery of the device.
STEP 0: CHECK DEVICE MODEL NO.
Please know that this page is exclusively meant for Samsung Galaxy Exhibit. Do not use the procedures discussed here on any other device of Samsung or any other company. You have been warned!
STEP 1: BACKUP YOUR DEVICE
Back up important data and stuff before you start playing around here as there are chances you might lose your apps and app-data (app settings, game progress, etc.), and in rare case, files on the internal memory, too.
For help on Backup and Restore, check out our exclusive page on that linked right below.
► ANDROID BACK UP AND RESTORE GUIDE: APPS AND TIPS
STEP 2: INSTALL LATEST DRIVER
You must have proper and working driver installed on your windows computer to be able to successfully root your Samsung Galaxy Exhibit.
In case you’re not sure, follow the link below for a definitive guide for installing driver for your Samsung device on your computer.
► SAMSUNG DEVICES DRIVERS INSTALLATION GUIDE
STEP 3: INSTALLATION INSTRUCTIONS
DOWNLOADSDownload the files given below and transfer it to a separate folder on your computer (just to keep things tidy, that is).
FIRMWARE FILE WIPE FILE ODIN FILE STEP-BY-STEP GUIDEImportant Note: Backup important files stored on internal SD card of your device, so that in case a situation arises requiring you to do a factory reset after flashing with Odin, which might delete internal sd card too, your files will remain safe on PC.
Extract/Unzip the Odin file, Odin_v3.09.zip on your computer (using 7-zip free software, preferably). You’ll get the following files:
Odin3 v3.09.exe
Odin3.ini
Extract the chúng tôi file from the T599-Pre-rooted.zip into the same folder where the Odin was extracted.
Disconnect the Galaxy Exhibit from PC if it is connected.
Boot your Samsung Galaxy Exhibit into Download Mode:
Power off your phone first and wait for 6-7 seconds after display is off
Press and hold these 3 buttons together until you see Warning! screen: Volume Down + Power + Home
Press Volume Up now to continue to Download Mode
If you don’t get the Added! message, here are some troubleshooting tips:
Make sure you have installed driver for Galaxy Exhibit as said above.
If you have already installed driver, then uninstall them and re-install back.
Connect using a different USB port on your PC.
Try a different USB cable. The original cable that came with your phone should work best, if not, try any other cable that’s new and of good quality.
Reboot phone and PC and then try again.
Load the firmware file (extracted in Step 1) into Odin as instructed below:
Now in the Option section of Odin, make sure that Re-Partition box is unchecked. (Auto Reboot and F. Reset Time boxes remain checked, while all other boxes remain unchecked.)
Double check the above two steps. (Step 7 and Step 8)
When you get PASS! message, your device will restart automatically. You can then disconnect your phone from PC.
If you see FAIL message instead of the PASS in Odin’s top left box, that’s a problem. Try this now: disconnect your Galaxy Exhibit from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 3 of this guide again.
Also, If device is Stuck at setup connection or on any other process, then too, try this: disconnect your Galaxy Exhibit from PC, close Odin, remove phone’s battery and put it back inside in 3-4 seconds, open Odin and then repeat from Step 3 of this guide again.
Similarly, flash the t599_wipe.tar.md5 file obtained from the t599_wipe.zip in the AP box of Odin. (This is just an empty cache file which is used to break the bootlops if you can’t get to recovery)
FEEDBACK US!
It was easy to root your Galaxy Exhibit, right? Let us know how you plan to use root privileges on your Galaxy Exhibit.
Your suggestions and queries, if any, are most welcomed!
Update the detailed information about Back To Stock/Downgrade Samsung Galaxy Trend Gt on the Bellydancehcm.com website. We hope the article's content will meet your needs, and we will regularly update the information to provide you with the fastest and most accurate information. Have a great day!